Search found 351 matches
- Thu Feb 22, 2024 7:08 pm
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
Well, Bruce Springsteen’s song “One Step Up” now carries extra meaning for me…long story short, I needed to remove the recently installed oil pan to eliminate a slight chafe between the rotating mass and the pan’s oil scraper… :roll: Back story: on trial fit of the pan, I snugged the pan down with a...
- Fri Feb 16, 2024 1:53 pm
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
Just chipping away at the old rock pile…
- Tue Feb 13, 2024 6:43 pm
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
Got a late start today due to a few unforeseen distractions, so only got a few done…😏 The drill guide worked out well, holes were drilled straight and the tap had no problem following the hole. I lined up each hole with the starter opening in the backing plate so I could drill and tap with no interf...
- Tue Feb 13, 2024 11:08 am
- Forum: Not Cobra stuff
- Topic: Power Tek
- Replies: 3
- Views: 373
Re: Power Tek
Thx Tom!
- Mon Feb 12, 2024 9:27 pm
- Forum: Not Cobra stuff
- Topic: Power Tek
- Replies: 3
- Views: 373
Power Tek
https://www.google.com/search?client=safari&sca_esv=6f64e94da92d3a6a&hl=en-us&sxsrf=ACQVn0-pG0ovX0h7o-k37WsV5a1q_tEzeA%3A1707768594041&q=POWER%20TEK&ludocid=11217340801352617036&ibp=gwp%3B0%2C7&lsig=AB86z5UI4kiPfrWpAGLlSvPnsoWU&kgs=6c39b7ca921f6f63&shndl=-1&so...
- Mon Feb 12, 2024 9:20 pm
- Forum: Not Cobra stuff
- Topic: Drag strip in Callahan?
- Replies: 2
- Views: 351
Re: Drag strip in Callahan?
We’ll have to do a cobra run and check it out…
- Mon Feb 12, 2024 9:10 pm
- Forum: Not Cobra stuff
- Topic: Crosseyed again...
- Replies: 4
- Views: 1057
Re: Crosseyed again...
Tom, just letting you know, the past few days I’ve had to login each time. It doesn’t remember me from day to day.
- Mon Feb 12, 2024 9:07 pm
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
Thx for dropping it off Tom! I have a 21/64 drill bit in a typical length, so that should work out. I fashioned a drill guide that should ensure straight drilled holes. I’ll post pictures tomorrow when I go through it, had too many distractions today.
- Mon Feb 12, 2024 9:53 am
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
Tom, I need 5/16-18 helicoils, do you have that size?
Never mind, Autozone has them…
Never mind, Autozone has them…
- Sun Feb 11, 2024 9:44 pm
- Forum: Cobra stuff
- Topic: Mike's GT40 gets redone
- Replies: 85
- Views: 213823
Re: Mike's GT40 gets redone
I think we’re in agreement Tom.